There are a number of different technologies that can be used to produce devices which convert light into electricity, and we are going to explore these in turn. There is always a balance to be struck between how well something works, and how much it costs to produce, and the same can be said for solar energy.

We take solar cells, and we combine them into larger units known as “modules,” these modules,” these modules can again be connected together to form arrays. Thus we can see that there is a hierarchy, where the solar cell is the smallest part.

Let us look into the structure and properties of solar “cells,” but bear in mind, when combined into modules and arrays, the solar “cells” here are mechanically supported by other materials-aluminum, glass, and plastic.

One of the materials that solar cells can be made from is silicon-this is the material that you find inside integrated circuits and transistors. There are good reasons for using silicon; it is the next most abundant element on earth after oxygen. When you consider that sand is silicon dioxide (SiO2), you realize that there is a lot of it out there!

Silicon can be used in several different ways to produce photovoltaic cells. The most efficient solar technology is that of “monocrystalline solar cells,” these are slices of silicon taken from a single, large silicon crystal. As it is a single crystal it has a very regular structure and no boundaries between crystal grains and so it performs very well. You can generally identity a monocrystalline solar cell, as it appears to be round or a square with rounded corners.

One of the caveats with this type of method, as you will see later, is that when a silicon crystal is “grown,” it produces a round cross-section solar cell, which does not fit well with making solar panels, as round cells are hard to arrange efficiently.

The next type of solar cell we will be looking at also made from silicon, is slightly different, it is a “polycrystalline” solar cell. Polycrystalline cells are still made from solid silicon; however, the process used to produce the silicon from which the cells are cut is slightly different. This results in “square” solar cells. However, there are many “crystals” in a polycrystalline cell, so they perform slightly less efficiently, although they are cheaper to produce with less wastage.

Now, the problem with silicon solar cells, as we will see in the next experiment, is that they are all effectively “batch produced” which means they are produced in small quantities, and are fairly expensive to manufacture. Also, as all of these cells are formed from “slices” of silicon, they use quite a lot of material, which means they are quite expensive.

Now, there is another type of solar cells, so-called “thin-film” solar cells. The difference between these and crystalline cells is that rather than using crystalline silicon, these use chemical compounds to semiconduct. The chemical compounds are deposited on top of a “substrate,” that is to say a base for the solar cell. There are some formulations that do not require silicon at all, such as Copper indium diselenide (CIS) and cadmium telluride. However, there is also a process called “amorphous silicon,” where silicon is deposited on a substrate, although not in a uniform crystal structure, but as a thin film. In addition, rather than being slow to produce, thin-film solar cells can be produced using a continuous process, which makes them much cheaper.

However, the disadvantage is that while they are cheaper, thin-film solar cells are less efficient than their crystalline counterparts.

When looking at the merits of crystalline cells and thin-film cells, we can see that crystalline cells produce the most power for a given area. However, the problem with them is that they are expensive to produce and quite inflexible (as you are limited to constructing panels from standard cell sizes and cannot change or vary their shape).

Efficiency of different cell types:

Cell material EfficiencyArea required to generate 1 KW peak power
Monocrystalline silicon 15-18% 7-9 m2
polycrystalline silicon 13-16% 8-11 m2
Thin-film copper indium diselenide (CIS) 7.5-9.5% 11-13 m2
Cadmium telluride 6-9% 14-18 m2
Amorphous silicon 5-8% 16-20 m2

By contrast, thin-film cells are cheap to produce, and the only factor limiting their shape is the substrate they are mounted on.This means that you can create large cells, and cells of different shapes and sizes, all of which can be useful in certain applications.

We are now going to take a detailed look at making two different types of solar cell, one will be a crystalline solar cell, and the other a thin-film solar cell. Both of the experiments are designed to be “illustrative,” rather than to actually make shape is the substrate they are mounted on. The technology required to make silicon solar cells is out of the reach of the home experimenter, so we are going to “illustrate” the process of how a solar cell is made, using things you can find in your kitchen. For thin-film solar cells, we are going to make an actual solar cell, which responds to light with changing electrical properties; however, the efficiency of our cell will be very poor, and it will not be able to generate a useful amount of electricity.

Explore more about Home Solar Power Systems and understand the uses and benefits of solar photovoltaic, solar panels, and many other informative tips on using alternative energy. Visit Earth For Energy today; master the true knowledge of using energy.

Chemical engineer and renewable energy enthusiast, Dr. Alan Ilicic presents innovative approaches to utilizing the energy of our life-giving sun. In thespirit of ideas worth spreading, TEDx is a program of local, self-organized events that bring people together to share a TED-like experience. At a TEDx event, TEDTalks video and live speakers combine to spark deep discussion and connection in a small group. These local, self-organized events are branded TEDx, where x = independently organized TED event. The TED Conference provides general guidance for the TEDx program, but individual TEDx events are self-organized.
Video Rating: 4 / 5